Influence of niobium and molybdenum addition on microstructure and wear behavior of laser-borided layers produced on Nimonic 80A-alloy

Laser alloying was used for production of thick layers on surface of Nimonic 80A-alloy. For laser surface modification, three types of pre-coated pastes were applied: with amorphous boron, with amorphous boron and molybdenum as well as with amorphous boron and niobium. The microstructure, hardness and wear resistance of produced layers were studied in details. The presence of different types of borides in re-melted zone depended on the paste composition and caused an increase in hardness up to about HV 1000. The wear resistance was evaluated by calculation of mass wear intensity factor I_mw and relative mass loss of specimen and counter-specimen. The wear behavior of the tested frictional pairs was determined by 3D interference microscopy, scanning electron microscopy equipped with EDS microanalyzer. The significant increase in abrasive wear resistance was observed in comparison to untreated Nimonic 80A-alloy. The lowest mass loss intensity factor was characteristic of laser-alloyed Nimonic 80A-alloy with boron and niobium (I_mw=1.234 mg/(cm²·h)). Laser alloyed-layers indicated abrasive wear mechanism with clearly visible grooves. Laser alloying with boron and niobium resulted in the additional oxidative wear mechanism. In this case, EDS patterns revealed presence of oxygen on the worn surface of specimen.     

Feasibility of utilizing 2304 duplex stainless steel rebar in seawater concrete: Passivation and corrosion behavior of steel rebar in simulated concrete environments

The feasibility of using 2304 duplex stainless steel rebar in seawater concrete was determined by studying the passivation and corrosion behavior of steel in solutions simulated curing and service stage of concrete, respectively. The results demonstrate that 2304 duplex stainless steel rebar could be used with seawater concrete because of a stable passive film formed on the steel surface during the curing stage of concrete even in the presence of 2 M chloride ions. However, due to the synergistic effect of concrete carbonation, the rebar suffered a corrosive attack by chloride due to the lack of OH^? inhibition.     

改性防护蜡对轮胎胎侧胶性能的影响

研究改性防护蜡对轮胎胎侧胶性能的影响。结果表明,与传统防护蜡相比,改性防护蜡异构烷烃质量分数较小,结晶尺寸小且致密程度高。改性防护蜡可在不影响胎侧胶硫化特性和物理性能的前提下,大幅提高胎侧胶抗喷霜性能,保证轮胎表面不受臭氧侵蚀,在防止裂纹产生的同时明显改善成品轮胎外观。     

蓝藻基生物降解共混膜的力学性能

以聚乙烯醇(PVA)和水华蓝藻为主要原料,通过溶液铺膜法制备了蓝藻/PVA共混膜,采用万能试验机,研究了不同助剂对蓝藻/PVA共混膜力学性能的影响。结果表明,蓝藻的添加显著降低了共混膜的力学性能。当添加比例为PVA的1/2时,膜的拉伸强度和断裂伸长率分别比无藻处理下降了65.89%和79.57%。甘油、尿素显著提升了蓝藻/PVA共混膜的断裂伸长率,当添加比例为蓝藻的1/2时,分别能使共混膜的断裂伸长率提高73.20倍和62.02倍。虽然柠檬酸、硅烷偶联剂能够提升蓝藻/PVA共混膜的拉伸强度,但只能在低剂量时促进断裂伸长率的小幅提高,当柠檬酸添加比例为蓝藻的1/40时,膜的断裂伸长率能提高4.41倍,而当硅烷偶联剂添加比例为蓝藻的1/20时,膜的断裂伸长率能提高1.49倍。尿素与甘油复合增塑,更有利于提升共混膜的断裂伸长率。硅烷偶联剂与甘油复合增塑,更有利于提升共混膜的拉伸强度。     

Ti6Al4V钛合金表面蓝色微弧氧化膜的制备及性能

利用微弧氧化技术在Ti6Al4V钛合金表面制备出蓝色微弧氧化膜。对微弧氧化膜的微观形貌和元素组成进行了分析,并对微弧氧化膜的显微硬度进行了测试。结果表明:微弧氧化膜表面光整,呈均匀深蓝色,其主要由Ti、Mn、O和C四种元素组成,还含有少量的V、Al和Si元素;微弧氧化膜的表面粗糙度约为0.159μm,与钛合金的表面粗糙度相近;微弧氧化膜的显微硬度为5 437.4 MPa,显著高于钛合金的显微硬度。     

The superlattice structure and self-adaptive performance of C–Ti/MoS2 composite coatings

To improve the self-adaptability of MoS₂ coating in different environments, the coatings were doped with functional C and Ti by unbalanced magnetron sputtering system. The clear superlattice structure with minimal modulation period was investigated by High Resolution Transmission Electron Microscope (HRTEM). The co-doped coatings have better mechanical properties due to the special structure and the formation of C–Mo, Ti–S and Ti–O bonds, and better lubrication performance in both high humidity and vacuum than those of the single-doped ones. The doped Ti not only facilitates the formation of the MoS₂ (002) basal plane, but also improves the oxidation resistance of the composite film. The degree of friction-induced graphitization on the wear tracks and the quality of transfer films on the wear scars are key factors affecting the lubrication performance of the composite film. In the high-humidity environment, the reasonable doping elements can promote the formation the high-quality transfer film by interacting with H₂O water molecules, which will benefit the lubrication of the coating better. Our findings deepen the understanding of MoS₂ composite coating and provide a new solution for improving the self-adaptability of the coating.     

Effects of the film thickness and poling electric field on photovoltaic performances of (Pb,La)(Zr,Ti)O3 ferroelectric thin film-based devices

The ferroelectric photovoltaic (FPV) effect obtained in inorganic perovskite ferroelectric materials has received much attention because of its large potential in preparing FPV devices with superior stability, high open-circuit voltage (V_oc) and large short-circuit current density (J_sc). In order to obtain suitable thickness for the ferroelectric thin film as light absorption layer, in which, the sunlight can be fully absorbed and the photo-generated electrons and holes are recombined as few as possible, we prepare Pb_0.93La_0.07(Zr_0.6Ti_0.4)_0.9825O₃ (PLZT) ferroelectric thin films with different layer numbers by the sol-gel method and based on these thin films, obtain FPV devices with FTO/PLZT/Au structure. By measuring photovoltaic properties, it is found that the device with 4 layer-PLZT thin film (~300 nm thickness) exhibits the largest V_oc and J_sc and the photovoltaic effect obviously depends on the value and direction of the poling electric field. When the device is applied a negative poling electric field, both the V_oc and J_sc are significantly higher than those of the device applied the positive poling electric field, due to the depolarization field resulting from the remnant polarization in the same direction with the built-in electric field induced by the Schottky barrier, and the higher the negative poling electric field, the larger the V_oc and J_sc. At a -333 kV/cm poling electric field, the FPV device exhibits the most superior photovoltaic properties with a V_oc of as high as 0.73 V and J_sc of as large as 2.11 μA/cm². This work opens a new way for developing ferroelectric photovoltaic devices with good properties.     

模内装饰薄膜滞热对成型工艺的影响分析

以模内装饰技术(IMD)测试平板为研究对象，利用仿真和实验方法分析薄膜滞热的影响因素及薄膜滞热对成型工艺的影响规律。结果表明，薄膜滞热使动模侧模具温度场变化滞后于定模侧温度场，且在实验条件下达到8.6 ℃的最大温度差；薄膜滞热随着模具温度的增加而降低，随熔体温度和薄膜厚度增加而升高；薄膜影响熔体的充模与冷却，造成产品冷却不均的现象；薄膜滞热导致产品翘曲变形增加。     

薄膜铂电阻元件稳定性测试与分析

高端军事应用环境对测温传感器提出了小结构、高精度、良好的长期稳定性等要求,采用溅射方式制备的薄膜铂电阻元件成为了首选。通过分析薄膜铂电阻元件的结构、工艺,探讨影响稳定性的主要因素,包括薄膜缺陷、杂质、电迁移、结构封装应用与温度应力等。选择薄膜铂电阻在水三相点下的电阻值作为稳定性的比较基准,设计了一款不大于3mK的高精度测试系统。通过对薄膜铂电阻元件进行高温电寿命试验和温度冲击试验,评估得出薄膜铂电阻元件长期稳定性达到10mK,满足设计需求。